ASTM D5084 PDF

GeoTesting Express is a provider of Soil Testing Services – ASTM D, Standard Test Methods for Measurement of Hydraulic Conductivity of Saturated Porous. All the Controls products ASTM D standard. Enter now!. Standard Test Method for Measurement of Hydraulic Conductivity of Saturated Porous Materials Using a Flexible Wall Permeameter.

In addition, it is either not feasible or too costly to produce multiple specimens that have uniform physical properties. The key criterion is that the requirements covered in Section 5 have to be met. There are six alternate methods or hydraulic systems that may be used to measure the hydraulic conductivity. NOTE 13—When the water pressure in a test specimen changes and the applied total stress is constant, the effective stress in the test specimen changes, which can cause volume changes that can invalidate the test results.

Other hydraulic systems or schematics that meet these objectives are acceptable. A typical standard triaxial system with external data acquisition system includes: Continue permeation until at least four values of hydraulic conductivity are obtained over an interval of time in which: Tightening the temperature control.

The ends of the test specimen shall be cut and not troweled troweling can seal off cracks, slickensides, or other secondary features that might conduct water? In making this height adjustment, make sure the water level in d084 headwater burette starts out below that of the tailwater burette. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

Any other measuring device meeting these requirements is acceptable. A superscript epsilon e indicates an editorial change since the last revision or reapproval.

The volume prior to dismantling the cell is used to determine the? NOTE 7—Soaking under vacuum is applicable when there are continuous air voids in the specimen e.

Therefore, where-ever practical use stainless steel? The requirements outlined in 5. Obtaining a specimen having a diameter of 36 mm 1. If boiling is used, care shall be taken not to evaporate an excessive amount of water, which can lead to a larger salt concentration in the permeant water than desired. Continue permeation until at least two or more values of hydraulic conductivity k are steady.

ASTM D, Test equipment Controls

The test specimen shall be mounted immediately in the permeameter. Typically a test can be performed using Methods D, E, or F within two to three days.

Users of this standard are cautioned that compliance with Practice D does not in itself assure reliable results. Follow us YouTube LinkedIn. TRITECH original high-performance load frames for triaxial tests, ideal solution for advanced and research laboratories that want to perform high dd5084 tests at.

Hydraulic conductivity varies with varying void ratio, which changes when the effective stress changes. Units other than seconds smeters metc. Distilled water can signi? Traps to prevent the accidental? It is beyond the scope of this standard to consider signi? The water content of the trimmings shall be determined in accordance with Method D to the nearest 0.

In addition, they are representative of the signi? In addition, there is continuity of in? The schematic of the hydraulic system in Fig. The temperature shall be periodically measured and recorded. Rather, these systems are intended for determining the hydraulic conductivity of a material as rapidly as possible. A typical standard triaxial system with built-in acquisition measurement includes: Methods A, B, and C take a longer period-of-time, from a few days to a few weeks depending on the hydraulic conductivity.

ASTM D5084

A controlled high-humidity room is usually used for this purpose. They shall be checked regularly to ensure that they are not clogged.

Additional guidance on other drilling and sampling methods is given in Guide D Alternatively, measurements of the change in height of the test specimen can be used to con? In designing this type of hydraulic system, the area of the tailwater tube aout is made signi? There are six alternate methods or hydraulic systems, that may be used to measure the hydraulic conductivity.

Measure and record these head losses at the start and end of each permeation trial as a minimum. In this measurement the last digit may be due to estimation, see 5. Relatively incompressible, saturated materials have B values that are somewhat less than 1. Any gradient equal to or less than the highest gradient yielding a similar hydraulic conductivity may be used for testing. The diameter and height of the specimen shall each be at least 6 times greater than the largest particle size within the specimen.

D — 03 X2. To determine the relationship between hydraulic conductivity and void ratio, the hydraulic conductivity test would have to be repeated at different effective stresses. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.